Egg Box Fully Automatic Die Cutting with Stripping Machine

Egg Box Fully Automatic Die Cutting with Stripping Machine

 

 
 

  1. FEEDER (Max reduce direct edge feeder)
  1. New up graded, exact same as Max minimize lead edge feeder, a lot more accurate and optimistic feeding.
  2. Exceptional jogger at feeder to put together for the achievable potential in line operation with pre feeder (optional).
  3. Pneumatic side drive information plates (remaining and appropriate sides).
  4. Remaining and correct side guides, individually placement adjustable and register aspect at decision per box layout.
  5. High vacuum blower with silencer and valving system.

 

  1. DIECUTTING Part
  1. Crank and worm gear, toggle travel program for the lower platen.
  2. The cellular platen stroke is improved from 71mm to 95mm for handling corrugated board (specially AB Flute) smoother.
  3. Stationary high precision upper platen.
  4. Safety doorway and die chaser basic safety locking program.
  5. Higher torque pneumatic clutch/break for good clutch on and dependable breaking, and particular air inlet technique to manage the air volume for easy device begin and stop.
  6. Air cushion beneath the reducing plate for straightforward cutting plate in and out.
  7. Equipment major travel.
  8. Overloading safety torque restrict clutch.
  9. Point out-of-the-art 3 cam index gripper chain generate.
  10. Heart line program suitable to Center Line II, can make the reducing die and stripping die centered quickly.
  11. Higher top quality precision alloy gripper bars, every with twelve special hardened grippers to make sure agency get of the sheet at large pace.
  12. Sheet arrival and departure verify image sensor.
  13. Remaining and proper entrance lay locking blocks, separating and synchronizing adjustment CZPT.
  14. Chain guidebook rail use VL compound to increase abrasive resistance and seismic resistance.
  15. Self-diagnostic difficulty exhibit.
  16. Digital speed display.
  17. Automatic recycling lubrication technique with oil force gauge and oil stress swap.
  18. Computerized principal gripper generate chain lubrication.

 

  1. STRIPPING Part
  1. Centerline method (compatible to Centerline II).
  2. 400mm higher stripping frame raiser improves the procedure place, more operator friendly.
  3. Motorized upper frame suspending hoister.
  4. Lead edge waste removal technique.
  5. Centerline technique for fast stripping die established up.

 

  1. Delivery
  1. Escalator delivery fork with non-end air cylinder for neat and positive supply and conveyor belt delivery desk to protect the sheets from scratches.
  2. Bundle supply with pre-established counter requesting only a single sheet interval in non-cease procedure at 4500S/H generation speed.
  3. The bundle delivery table can be prepared for future relationship with breaker for in line procedure (to be needed at purchase).
  4. Total stripping with/CZPT lead edge waste stripping convertible by 1 button, no instrument adjust, much more operator friendly and safe operation.
  5. CZPT loaded adjustable chain stress back again buffering wheel to maintain the chain tension consistent and sleek gripper bar motion.

 

No. Model RYPE-1620SA
one Highest Sheet Dimension 1620x1200mm
two Minimum Sheet Size 650x450mm
3 Greatest Chopping Dimensions 1600x1180mm
4 Internal CZPT Measurement 1630x1210mm
five Optimum Mechanical Pace 5000 cycles/hour
six Highest Chopping Stress 400 tons
seven Inventory Range E, B,C,A and AB flute corrugated board (one~8.5mm)
8 Minimal Gripper Margin 6~12mm
nine Bare minimum Gripper Squander 12mm(Length from very first knife to paper edge)
ten Reducing Rule Height 23.8mm
eleven Overall Electricity Necessary 35 KW
twelve Primary Motor Energy 22 KW
13 CZPTal Electrical power 380V, 50HZ, 3-phase
fourteen Air Pump Displacement .7m³/min
fifteen Mobile Reduce Platen Adjusting Assortment ±1.5mm
sixteen Net Fat of Device 32 tons
seventeen Gross Weight of Device 39.five tons
eighteen Device Dimensions (LxWxH) 9980×5670 x2480 mm (consists of walking board)

Egg Box Fully Automatic Die Cutting with Stripping Machine

Tags